Media Over QUIC Y. Liu Internet-Draft Alibaba Inc. Intended status: Standards Track M. Jiang Expires: 23 May 2027 R. Wu Ant Group. C. Jennings Cisco Systems S. Nandakumar Cisco 19 November 2026 MoQ Feedback draft-liu-moq-feedback-03 Abstract This document defines Media over QUIC Feedback (MQF), an extension to Media over QUIC Transport (MOQT) that enables delivery quality information about media Objects to be reported using Feedback Tracks. It defines how Feedback Tracks are associated with media Tracks, established, forwarded through Relays, and consumed, together with the MQF report format and capability negotiation. MQF complements transport-layer signals with per-Object delivery information. Discussion Venues This note is to be removed before publishing as an RFC. Discussion of this document takes place on the Media Over QUIC Working Group mailing list (moq@ietf.org), which is archived at https://mailarchive.ietf.org/arch/browse/moq/. Source for this draft and an issue tracker can be found at https://github.com/Yanmei-Liu/draft-moq-multimodal-feedback. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Liu, et al. Expires 23 May 2027 [Page 1] Internet-Draft MoQ Feedback November 2026 Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 23 May 2027. Copyright Notice Copyright (c) 2026 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1. Conventions and Definitions . . . . . . . . . . . . . . . 4 1.2. Scope and Non-Goals . . . . . . . . . . . . . . . . . . . 5 2. Motivation . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. Architecture . . . . . . . . . . . . . . . . . . . . . . . . 7 3.1. Feedback Model . . . . . . . . . . . . . . . . . . . . . 7 3.2. Feedback for Bidirectional Media . . . . . . . . . . . . 8 3.3. Feedback Routing through Relays . . . . . . . . . . . . . 9 4. Feedback Track . . . . . . . . . . . . . . . . . . . . . . . 10 4.1. Track Definition . . . . . . . . . . . . . . . . . . . . 10 4.2. Track Naming . . . . . . . . . . . . . . . . . . . . . . 12 4.3. Track Establishment and Lifecycle . . . . . . . . . . . . 13 4.4. Transport and Priority . . . . . . . . . . . . . . . . . 16 5. Feedback Report Format . . . . . . . . . . . . . . . . . . . 16 5.1. Report Structure . . . . . . . . . . . . . . . . . . . . 17 5.2. Object Entry . . . . . . . . . . . . . . . . . . . . . . 18 5.2.1. Group ID . . . . . . . . . . . . . . . . . . . . . . 18 5.2.2. Object ID . . . . . . . . . . . . . . . . . . . . . . 18 5.2.3. Status . . . . . . . . . . . . . . . . . . . . . . . 18 5.2.4. Receive Timestamp Delta . . . . . . . . . . . . . . . 18 5.3. Delivery Status Codes . . . . . . . . . . . . . . . . . . 19 5.3.1. RECEIVED_LATE Determination . . . . . . . . . . . . . 20 5.3.2. NOT_RECEIVED Reporting Timing . . . . . . . . . . . . 20 5.3.3. PARTIALLY_RECEIVED . . . . . . . . . . . . . . . . . 21 5.3.4. NOT_DELIVERED . . . . . . . . . . . . . . . . . . . . 21 Liu, et al. Expires 23 May 2027 [Page 2] Internet-Draft MoQ Feedback November 2026 5.4. Summary Stats Block . . . . . . . . . . . . . . . . . . . 22 5.4.1. Report Interval . . . . . . . . . . . . . . . . . . . 23 5.4.2. Total Objects Evaluated . . . . . . . . . . . . . . . 23 5.4.3. Objects Received . . . . . . . . . . . . . . . . . . 23 5.4.4. Objects Received Late . . . . . . . . . . . . . . . . 23 5.4.5. Objects Lost . . . . . . . . . . . . . . . . . . . . 23 5.4.6. Avg Inter-Arrival Delta . . . . . . . . . . . . . . . 23 5.4.7. Objects Not Delivered . . . . . . . . . . . . . . . . 24 5.5. Optional Media Metrics . . . . . . . . . . . . . . . . . 24 5.6. Report Size Control . . . . . . . . . . . . . . . . . . . 27 5.6.1. Encoding Example . . . . . . . . . . . . . . . . . . 28 6. Negotiation . . . . . . . . . . . . . . . . . . . . . . . . . 29 6.1. Setup Option . . . . . . . . . . . . . . . . . . . . . . 29 6.2. Capability Negotiation Rules . . . . . . . . . . . . . . 31 6.3. Behavior When Option Not Declared . . . . . . . . . . . . 32 6.4. Runtime Capability Change . . . . . . . . . . . . . . . . 32 7. Media Subscriber Behavior . . . . . . . . . . . . . . . . . . 32 7.1. Arrival Time Recording . . . . . . . . . . . . . . . . . 32 7.2. Delivery Status Determination . . . . . . . . . . . . . . 32 7.3. MQF Generation Timing . . . . . . . . . . . . . . . . . . 33 7.4. Object Entry Selection . . . . . . . . . . . . . . . . . 33 7.5. Exception Handling . . . . . . . . . . . . . . . . . . . 34 8. Media Publisher Behavior . . . . . . . . . . . . . . . . . . 34 8.1. Report Consumption . . . . . . . . . . . . . . . . . . . 34 9. Application Usage Considerations . . . . . . . . . . . . . . 34 9.1. Relay-Local Feedback Consumption . . . . . . . . . . . . 34 9.2. Source Adaptation with End-to-End Feedback . . . . . . . 35 9.3. Selecting Feedback Tracks with TopN . . . . . . . . . . . 36 9.4. Cache Feedback as an Optional Extension . . . . . . . . . 37 9.5. Relay-Derived Feedback from Multiple Subscribers . . . . 38 9.6. Uplink-Constrained Simulcast Publisher . . . . . . . . . 39 9.7. Feedback for Many Media Tracks . . . . . . . . . . . . . 40 10. Security Considerations . . . . . . . . . . . . . . . . . . . 40 11. Privacy Considerations . . . . . . . . . . . . . . . . . . . 41 12. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 41 13. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 42 14. References . . . . . . . . . . . . . . . . . . . . . . . . . 42 14.1. Normative References . . . . . . . . . . . . . . . . . . 42 14.2. Informative References . . . . . . . . . . . . . . . . . 43 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 43 Liu, et al. Expires 23 May 2027 [Page 3] Internet-Draft MoQ Feedback November 2026 1. Introduction Media over QUIC Transport (MOQT, [MoQTransport]) is a QUIC-based publish/subscribe media transport framework. In low-latency applications, a Media Publisher can benefit from knowing whether media Objects were received completely and within an application- relevant deadline. QUIC acknowledgments and receive timestamps provide transport-layer information, but they do not directly express these Object-level delivery outcomes or application state. Transport-layer feedback is also scoped to an individual QUIC connection. When media traverses one or more Relays, feedback on the Media Original Publisher's connection describes delivery only to its adjacent peer, not the cumulative delivery outcome observed by the downstream Media Subscriber. This document defines Media over QUIC Feedback (MQF), a MoQ-layer mechanism for carrying such information in Feedback Tracks. MQF reports are associated with a media Track and can be consumed by an adjacent Media Publisher or delivered across Relays to the Media Original Publisher. 1.1. Conventions and Definitions The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. The following terms are used throughout this document: * *MOQT:* Media over QUIC Transport, following [MoQTransport]. * *Object:* An addressable unit whose Payload is a sequence of bytes, following [MoQTransport]. * *Media Publisher:* The Publisher of a media Track on a given MOQT session. * *Media Subscriber:* A Subscriber of a media Track on a given MOQT session. * *Relay:* A MoQ node that forwards media Tracks or Feedback Tracks between Publishers and Subscribers, following [MoQTransport]. * *Media Original Publisher:* The Original Publisher, as defined by [MoQTransport], of the media Track associated with a Feedback Track. Liu, et al. Expires 23 May 2027 [Page 4] Internet-Draft MoQ Feedback November 2026 * *Adjacent Media Publisher:* The Publisher from which a Media Subscriber receives the associated media Track on a particular MOQT session. It can be a Relay or the Media Original Publisher. * *Feedback Publisher:* The Publisher of a Feedback Track, typically a Media Subscriber of the associated media Track or a Relay generating a new Feedback Track. * *Feedback Subscriber:* A Subscriber of a Feedback Track. An intermediate Relay can subscribe to a Feedback Track for forwarding without consuming its Payload. * *Feedback Consumer:* The terminal Feedback Subscriber that interprets MQF reports. The Feedback Consumer is the Adjacent Media Publisher for HOP_FEEDBACK and the Media Original Publisher for ORIGIN_FEEDBACK. * *Feedback Track:* A MoQ Track that carries MQF reports. * *Feedback Type:* A Relay-visible Track Property that identifies whether a Feedback Track terminates at the Adjacent Media Publisher or is delivered to the Media Original Publisher. * *MQF (Media over QUIC Feedback):* A feedback report at the MoQ layer containing per-Object delivery status for an associated media Track. 1.2. Scope and Non-Goals This document specifies: * how a Feedback Track is associated with a media Track; * how Feedback Tracks are established, forwarded, and terminated; * the Relay behavior associated with each Feedback Type; * the MQF report format and capability negotiation; and * endpoint behavior required to generate and interpret interoperable MQF reports. This document does not specify: * how an application adjusts encoding, generation, subscription, or scheduling in response to MQF; Liu, et al. Expires 23 May 2027 [Page 5] Internet-Draft MoQ Feedback November 2026 * the algorithm a Relay uses to derive or aggregate a new MQF report from downstream observations and local state; * how Relays are deployed or configured, including path selection, Relay-to-Relay monitoring, and path remediation. An implementation can use MQF reports as one input when adapting media or local forwarding behavior. Such use does not replace transport congestion control, and an implementation MUST NOT use MQF to bypass the sending limits imposed by its congestion controller. 2. Motivation QUIC-layer feedback mechanisms such as acknowledgments and Receive Timestamps operate at the packet level and do not directly carry the following MoQ- or application-level information: +=================+=================================================+ | Blind Spot | Description | +=================+=================================================+ | Object | Transport acknowledgment does not state whether | | Delivery | a complete Object was available before an | | Outcome | application deadline | +-----------------+-------------------------------------------------+ | Object-Level | Packet timing does not directly express the | | Timing | arrival relationship between media Objects | +-----------------+-------------------------------------------------+ | Application | The transport does not know playback headroom | | State | or application consumption state | +-----------------+-------------------------------------------------+ | End-to-End | Transport feedback is scoped to one QUIC | | Delivery | connection and does not describe the cumulative | | across Relays | delivery outcome across a Relay chain | +-----------------+-------------------------------------------------+ Table 1 Addressing these blind spots requires a feedback mechanism that reports delivery outcomes at MOQT Object granularity and associates those observations with the corresponding media Track. Liu, et al. Expires 23 May 2027 [Page 6] Internet-Draft MoQ Feedback November 2026 In a direct deployment, the Adjacent Media Publisher is also the Media Original Publisher. When media traverses one or more Relays, these roles are separated. A feedback mechanism therefore needs to support both local consumption by the Adjacent Media Publisher and delivery of downstream observations across the Relay chain to the Media Original Publisher. The latter cannot be inferred from transport feedback on the Media Original Publisher's immediate connection. 3. Architecture 3.1. Feedback Model A Feedback Track is a normal MOQT Track whose Objects carry MQF reports. MQF introduces no new QUIC frame or MOQT control message type. The associated media Track identifies the Object sequence being reported, and the Feedback Type identifies the intended Feedback Consumer and Relay behavior. MQF operates at Object granularity. The interpretation of an Object as a frame, chunk, or other media unit is defined by the media format or application. MQF complements, rather than replaces, transport-layer signals. QUIC acknowledgments describe packet delivery on one QUIC connection, and receive timestamps such as [quic-receive-ts] can provide additional packet timing information. MQF describes delivery outcomes using media Object coordinates and can carry application-level observations such as playout headroom. An ORIGIN_FEEDBACK report can reflect the cumulative delivery outcome observed downstream of the Media Original Publisher, but it does not identify which Relay hop or path segment caused that outcome. Hop- by-hop path diagnosis is not defined by MQF. Liu, et al. Expires 23 May 2027 [Page 7] Internet-Draft MoQ Feedback November 2026 +========================+===============+==========================+ | Signal | Granularity | Information Provided | | | and Scope | | +========================+===============+==========================+ | QUIC | Packet level | Transport delivery and | | acknowledgment and | on one QUIC | timing information | | receive timestamps | connection | | +------------------------+---------------+--------------------------+ | MQF | Object level, | Object delivery status | | | hop-local or | and optional application | | | across Relays | observations | +------------------------+---------------+--------------------------+ Table 2 3.2. Feedback for Bidirectional Media Feedback direction is defined relative to the associated media Track, not by an endpoint role or an application-specific direction label. A Media Subscriber that generates feedback acts as the Feedback Publisher. The intended Feedback Consumer is determined by the Feedback Type: the Adjacent Media Publisher for HOP_FEEDBACK, or the Media Original Publisher for ORIGIN_FEEDBACK. An endpoint can be a Media Publisher for one Track and a Media Subscriber for another Track. Each media Track can independently have one or more associated Feedback Tracks: Endpoint A Endpoint B |--- media Track A ------------>| B: Media Subscriber |<-- Feedback Track A -----------| B: Feedback Publisher | | |<-- media Track B --------------| A: Media Subscriber |--- Feedback Track B ---------->| A: Feedback Publisher The two Feedback Tracks use the same report format and establishment rules. The associated media Track identifies the media flow being reported, and each Feedback Track independently declares HOP_FEEDBACK or ORIGIN_FEEDBACK. The PUBLISH_FEEDBACK and SUBSCRIBE_FEEDBACK Setup Option bits indicate whether the endpoint that declares them can publish or subscribe to Feedback Tracks on the current MOQT session. Liu, et al. Expires 23 May 2027 [Page 8] Internet-Draft MoQ Feedback November 2026 3.3. Feedback Routing through Relays MQF supports deployments in which feedback is consumed by the Adjacent Media Publisher as well as deployments in which feedback is delivered to the Media Original Publisher. The Feedback Type Track Property defined in Section 4.1 identifies the intended consumer and required Relay behavior. In a cascaded Relay architecture, media from a Media Original Publisher traverses multiple Relays before reaching a Media Subscriber. The Media Subscriber is the feedback source, the Relay adjacent to the Media Subscriber can consume its reported delivery outcomes, and the Relay chain can carry a separate Feedback Track to the Media Original Publisher. Media Media Original Publisher -> ... -> L2 -> L1 -> Media Subscriber HOP_FEEDBACK L1 <- Media Subscriber Relay-generated ORIGIN_FEEDBACK Media Original Publisher <- ... <- L2 <- L1 Subscriber-generated ORIGIN_FEEDBACK Media Original Publisher <- ... <- L2 <- L1 <- Media Subscriber The following Feedback Tracks serve different consumers: * A HOP_FEEDBACK Track carries delivery outcomes observed by the Media Subscriber and terminates at the L1 Relay for local interpretation. * The L1 Relay can derive a new ORIGIN_FEEDBACK Track from received HOP_FEEDBACK and other information available to the Relay when configured to do so. When doing so, the Relay acts as a new Feedback Publisher and publishes a distinct Feedback Track in the context of its upstream media Track. * An ORIGIN_FEEDBACK Track can be published by a Media Subscriber or a Relay and can traverse zero or more Relays. Its MQF Payload remains opaque to intermediate Relays. Subscriber-generated ORIGIN_FEEDBACK requires the Media Original Publisher to have sufficient application context to interpret the report and its associated media Track coordinates. Liu, et al. Expires 23 May 2027 [Page 9] Internet-Draft MoQ Feedback November 2026 A Media Subscriber behind an L1 Relay SHOULD use HOP_FEEDBACK when the report requires Relay-local interpretation or translation into the context of an upstream media Track. It MAY instead publish ORIGIN_FEEDBACK when the Media Original Publisher has sufficient application context to interpret the report and its associated media Track coordinates. The relative importance of the two Feedback Types depends on the application. For example, a deployment can use HOP_FEEDBACK as input to local Track selection or forwarding behavior and ORIGIN_FEEDBACK as input to source adaptation. A Relay that derives a report from one or more downstream reports acts as a new Feedback Publisher and publishes a distinct Feedback Track. The base MQF format does not define the semantics of deriving ORIGIN_FEEDBACK from downstream reports, whether from one report or by aggregating multiple reports. Such derivation requires an extension or application agreement that defines observation provenance, timestamp handling, metric interpretation, and, when applicable, the represented Media Subscribers and aggregation method. 4. Feedback Track 4.1. Track Definition The Feedback Track is a normal MoQ Track where the Payload of each Object is an MQF report. Each MQF report is published as an independent Object with monotonically increasing Object ID within a Group. Each Feedback Track has exactly one Feedback Type and MUST NOT mix HOP_FEEDBACK and ORIGIN_FEEDBACK. The type controls Track distribution and is carried in the Relay-visible MQF_FEEDBACK_TYPE Track Property. A Feedback Publisher that generates both types MUST publish two distinct Feedback Tracks. The MQF_FEEDBACK_TYPE Track Property has an MOQT variable-length integer (vi64) value, encoded as specified in [MoQTransport], Section 8.1: Liu, et al. Expires 23 May 2027 [Page 10] Internet-Draft MoQ Feedback November 2026 +=======+=================+=======================================+ | Value | Name | Description | +=======+=================+=======================================+ | 0x00 | HOP_FEEDBACK | Intended for the Adjacent Media | | | | Publisher on the current MOQT session | +-------+-----------------+---------------------------------------+ | 0x01 | ORIGIN_FEEDBACK | Intended for the Media Original | | | | Publisher across zero or more Relays | +-------+-----------------+---------------------------------------+ Table 3 Every Feedback Track MUST include the MQF_FEEDBACK_TYPE Track Property (TBD2 - experimental number 0x37FE) in its PUBLISH Track Properties. This Property is immutable for the lifetime of the Track. A Relay that recognizes it MUST NOT modify or remove it. A Relay that does not recognize it forwards and caches it according to the unknown Property rules in [MoQTransport]. An MQF-aware Relay uses this Property without inspecting MQF Object Payloads. A terminal Feedback Consumer that receives an unsupported value MUST reject the Feedback Track. The Group division strategy for Feedback Track is implementation- defined. Each MQF report is self-contained, and a newer report supersedes the value of an older one. It is therefore RECOMMENDED that a Feedback Publisher start a new Group for each MQF report, with the report as Object 0 of that Group, so that a delayed or lost report does not block delivery of newer reports on the same stream. A Feedback Publisher that places multiple reports in one Group accepts that a retransmitted earlier report can delay later reports. Each Feedback Track MUST be associated 1:1 with a media Track. The association is encoded in the Feedback Full Track Name (Section 4.2) and is not repeated in MQF reports. This Full Track Name binding is the media Track binding mechanism defined by this document; no per- Object binding parameter is required. When feedback is needed for multiple media Tracks, independent Feedback Tracks MUST be established separately. Each Feedback Publisher or publication session MUST use a distinct Feedback Full Track Name. This prevents independent publishers from producing different Payloads for the same Group ID and Object ID on what MOQT would otherwise treat as a single Track. Liu, et al. Expires 23 May 2027 [Page 11] Internet-Draft MoQ Feedback November 2026 4.2. Track Naming The Feedback Full Track Name carries the information that Relays need to distribute a Feedback Track without inspecting Object Payloads. Let ++ denote appending fields to a Track Namespace tuple. A Feedback Track MUST use: * *Track Namespace:* The media Track Namespace with three fields appended in this order: the literal mqf, the feedback type label, and the feedback source ID. * *Track Name:* The Track Name of the associated media Track. The feedback-type-label is the ASCII string hop-feedback for HOP_FEEDBACK or origin-feedback for ORIGIN_FEEDBACK. It enables Namespace prefix matching. The label MUST agree with the MQF_FEEDBACK_TYPE Track Property. A node that detects a mismatch MUST reject the Feedback Track. The feedback-source-id is an opaque, non-empty byte string selected by the Feedback Publisher. It MUST distinguish that publisher and publication session from every other Feedback Publisher and session for the associated media Track. It is not required to identify a user and MUST NOT be interpreted as a user identity. A publisher MUST select a new value before reusing a Group ID and Object ID pair or restarting its Report Sequence space. To limit linkability across sessions, a Feedback Publisher SHOULD select a feedback-source-id that is randomly generated for each publication session and is not derived from a stable user, device, or network identifier (see Section 11). For example, feedback for media Full Track Name (example.com, meeting, audio_response) can use: (example.com, meeting, mqf, hop-feedback, subscriber-17, audio_response) (example.com, meeting, mqf, origin-feedback, relay-l1-4, audio_response) The same naming construction applies independently to every media Track. The associated media Track determines the media direction being reported; a separate direction prefix is not used. A node receiving a PUBLISH for a Feedback Track reconstructs the associated media Full Track Name by removing the final three Namespace fields and retaining the Feedback Track Name. If it cannot identify the associated media Track or does not support the indicated type, it SHOULD respond with REQUEST_ERROR. Liu, et al. Expires 23 May 2027 [Page 12] Internet-Draft MoQ Feedback November 2026 4.3. Track Establishment and Lifecycle The Feedback Track is established by the Feedback Publisher (a Media Subscriber or a Relay generating new feedback) through MOQT's PUBLISH / REQUEST_OK exchange on a bidirectional request stream. In [MoQTransport], PUBLISH_OK is a descriptive alias for REQUEST_OK, not a separate wire message type. The MQF capabilities required by Section 6 MUST be negotiated before establishment. For a HOP_FEEDBACK Track, the terminal Feedback Consumer is the Adjacent Media Publisher on that MOQT session. The Feedback Consumer accepts the PUBLISH and MUST NOT advertise or forward that Feedback Track on another MOQT session. An L1 Relay that generates ORIGIN_FEEDBACK is a new Feedback Publisher. It uses a new Feedback Full Track Name, Report Sequence space, and MQF Payload. It can derive that Payload from HOP_FEEDBACK, local media transmission state, and the mapping between its upstream and downstream media Tracks. An ORIGIN_FEEDBACK type does not create a route by itself. Before feedback Objects can be delivered, an interest and authorization chain MUST be established between the Media Original Publisher and the Feedback Publisher: 1. The Media Original Publisher, acting as a Feedback Subscriber, expresses interest in the origin-feedback Namespace for the media Track. It can use SUBSCRIBE_TRACKS for the corresponding Namespace prefix, or use deployment-specific prior interest and authorization as permitted by [MoQTransport]. 2. Each intermediate Relay binds the Feedback Track to the media forwarding state identified by Section 4.2. It propagates feedback interest only to downstream peers to which it forwards the associated media Track. Feedback Objects travel in the opposite direction, toward the peer from which the Relay received that media Track. 3. The Feedback Publisher sends PUBLISH for its unique Feedback Full Track Name. Each hop uses the PUBLISH / REQUEST_OK and SUBSCRIBE / SUBSCRIBE_OK procedures in [MoQTransport] to establish forwarding with Forward State 1. SUBSCRIBE_NAMESPACE discovers published Namespaces; it does not request PUBLISH messages for their Tracks. SUBSCRIBE_TRACKS expresses that Track interest in [MoQTransport]. Liu, et al. Expires 23 May 2027 [Page 13] Internet-Draft MoQ Feedback November 2026 PUBLISH_NAMESPACE is not a route discovery mechanism. A Relay MUST NOT use it to search a richly connected Relay topology for a path to the Media Original Publisher. A Relay forwards ORIGIN_FEEDBACK only toward the peer from which it received the associated media Track, and MUST NOT forward it back toward the Feedback Publisher or another downstream media peer. If there is no unique reverse media-path binding, the Relay MUST reject the Feedback Track. These rules prevent a feedback loop in the single-upstream media topology defined by this document. If any hop has no matching interest, lacks authorization, has no media-path binding, or rejects the request, that hop MUST reject establishment using the applicable MOQT request error. The Feedback Publisher MUST NOT send MQF Objects until its PUBLISH is accepted. It MAY continue or fall back to a separately established HOP_FEEDBACK Track, but it MUST NOT relabel a rejected Track to bypass the failure. Relays route both Feedback Track types solely from the Full Track Name and MQF_FEEDBACK_TYPE Track Property. In accordance with [MoQTransport], the Object Payload is opaque to a Relay and is not processed to make a forwarding decision. An ORIGIN_FEEDBACK MQF Payload can therefore be protected between the Feedback Publisher and the Media Original Publisher. A HOP_FEEDBACK MQF Payload can be protected for its adjacent terminal Feedback Consumer. *Direct Establishment Flow Example:* Both endpoints have completed the MQF Setup exchange in Section 6. The Media Original Publisher has prior interest in and authorization to receive the Feedback Track. The diagram omits request identifiers and other MOQT fields. Liu, et al. Expires 23 May 2027 [Page 14] Internet-Draft MoQ Feedback November 2026 Media Subscriber Media Original Publisher (Media Subscriber / (Media Publisher / Feedback Publisher) Feedback Subscriber) | | | SUBSCRIBE(track=audio_response) | (1) Subscribe media Track |----------------------------------->| | SUBSCRIBE_OK | |<-----------------------------------| | | | PUBLISH( | (2) Publish origin-feedback Track | namespace=media_namespace ++ | | ("mqf", "origin-feedback", | | "subscriber-17"), | | track=audio_response, | | property=MQF_FEEDBACK_TYPE(1)) | |----------------------------------->| | REQUEST_OK | |<-----------------------------------| | | | [Object: MQF seq=0] | (3) Send MQF report |----------------------------------->| | [Object: MQF seq=1] | |----------------------------------->| | ... | *Lifecycle Rules:* The Feedback Track lifecycle SHOULD align with the subscribed media Track it covers. After the media Track publisher sends PUBLISH_DONE for the media Track, the Feedback Publisher SHOULD send PUBLISH_DONE for the Feedback Track after transmitting the final MQF report and stop publishing Objects. When the Media Subscriber ends its subscription to the media Track, for example when switching to a different representation, it SHOULD send PUBLISH_DONE for the associated Feedback Track after transmitting any final MQF report. When a MOQT session carrying a Feedback Track is disconnected, a Relay MUST discard the associated forwarding state and MUST NOT re- advertise the old Feedback Track after reconnecting. The Feedback Publisher establishes a new Feedback Track with a new feedback- source-id; its Report Sequence SHOULD restart from 0. Feedback is time-sensitive. A Feedback Publisher SHOULD use the MAX_CACHE_DURATION Track Property defined by [MoQTransport] to bound the period for which MQF Objects can be served from cache. A terminal feedback consumer MUST NOT apply an MQF report from a previous publication session. Liu, et al. Expires 23 May 2027 [Page 15] Internet-Draft MoQ Feedback November 2026 4.4. Transport and Priority The Feedback Track SHOULD be carried over QUIC Stream (consistent with ordinary MoQ Objects). Feedback is most useful when the path is congested, which is also when it is most likely to be delayed. If a Feedback Track is scheduled behind the media it describes, reports can be delayed until they no longer reflect current conditions. The priority of a Feedback Track ([MoQTransport], Section 5.1) SHOULD therefore be no lower than the priority of the media Track it describes. Example priority assignment: +================+=====================+=============+ | Track Type | Subscriber Priority | Description | +================+=====================+=============+ | audio_response | 0 (highest) | Audio media | +----------------+---------------------+-------------+ | Feedback Track | 1 | MQF report | +----------------+---------------------+-------------+ | video_response | 2 | Video media | +----------------+---------------------+-------------+ Table 4 A high priority does not entitle feedback to a large share of capacity. A Feedback Publisher MUST bound the rate of each Feedback Track, for example by limiting report frequency (Section 7.3) and report size (Section 5.6), so that feedback remains a small fraction of the media rate it describes. A stale report has little value once a newer report is available. A Feedback Publisher SHOULD use a delivery timeout ([MoQTransport]) no larger than a small multiple of its report interval, so that undelivered reports are abandoned rather than retransmitted after newer reports exist. 5. Feedback Report Format This section defines the binary encoding format of an MQF report. All integer fields use QUIC Variable-Length Integer encoding (RFC 9000, Section 16) unless otherwise specified. This MQF Payload encoding is distinct from the MOQT vi64 encoding used for Setup Options and Track Properties. Relays forwarding MQF Objects preserve the Payload bytes without translating between these encodings. Liu, et al. Expires 23 May 2027 [Page 16] Internet-Draft MoQ Feedback November 2026 Fields marked as "signed encoding" use ZigZag mapping and are transmitted as unsigned QUIC varint: * *Encoding:* unsigned = (signed << 1) ^ (signed >> 63) * *Decoding:* signed = (unsigned >>> 1) ^ -(unsigned & 1) Mapping examples: 0 -> 0, -1 -> 1, 1 -> 2, -2 -> 3, 2 -> 4. 5.1. Report Structure MQF Report { Report Timestamp (i), Report Sequence (i), Object Entry Count (i), Object Entry (..) ..., Summary Stats (..), Optional Metric Count (i), Optional Metric (..) ..., } This document defines MQF report format version 0. The MOQT_FEEDBACK Setup Option (Section 6.1) declares support for this format; it does not negotiate a separate version number. The format version is not repeated in each report. Each MQF report describes Object delivery status for a single media Track associated with its Feedback Track (1:1 association, see Section 4.1). *Report Timestamp (varint):* The moment when the report is generated, using the Feedback Publisher's local monotonic clock value in microseconds. This value is only used for Receive Timestamp Delta chain anchoring and report ordering, not for cross-end time alignment. Monotonic clock MUST be used. The epoch of this clock is chosen by the Feedback Publisher and has no meaning to the Feedback Consumer; it MUST remain constant for the lifetime of a Feedback Track. *Report Sequence (varint):* Monotonically increasing from 0 independently for each Feedback Track. A gap can indicate an omitted report only when the publication policy for that Track requires a contiguous Report Sequence. An Object ID gap alone, without a Prior Object ID Gap property as defined by [MoQTransport], MUST NOT be interpreted as feedback loss. Because HOP_FEEDBACK and ORIGIN_FEEDBACK use separate Tracks, terminating one type cannot create sequence gaps in the other type's sequence space. Liu, et al. Expires 23 May 2027 [Page 17] Internet-Draft MoQ Feedback November 2026 *Object Entry Count (varint):* Number of Object Entries that follow. When the value is 0, the report contains only Summary Stats (for heartbeat purposes). 5.2. Object Entry Object Entry { Group ID (i), Object ID (i), Status (i), [Receive Timestamp Delta (i)], } Object Entries within the same MQF MUST be sorted in ascending order by (Group ID, Object ID). 5.2.1. Group ID The Group ID (varint) of the Object in the associated media Track. 5.2.2. Object ID The Object ID (varint) within the identified Group of the associated media Track. The media Full Track Name from Section 4.2, Group ID, and Object ID together identify the media Object being reported. A Relay forwarding the same media Track preserves these coordinates. A Relay that changes the Full Track Name or media Object coordinates is publishing a different media Track and MUST NOT associate its Feedback Track with the pre-transformation media Track. 5.2.3. Status Delivery status code (varint), see Section 5.3 for values. 5.2.4. Receive Timestamp Delta Conditional presence field (varint, signed encoding): Present only when Status is RECEIVED (0x00) or RECEIVED_LATE (0x01). Encoding rules: * *First received Object within the same MQF* (i.e., the first entry with Status RECEIVED or RECEIVED_LATE when iterating through the list): Let R be the Report Timestamp and T_i be the Object's arrival time, both in microseconds on the Feedback Publisher's local monotonic clock. The signed Delta is T_i - R. Liu, et al. Expires 23 May 2027 [Page 18] Internet-Draft MoQ Feedback November 2026 * *Subsequent received Objects:* Let T_j be the arrival time of the most recent preceding entry with Status RECEIVED or RECEIVED_LATE. The signed Delta is T_i - T_j. A decoder reconstructs T_i as R + Delta for the first received Object Entry and as T_j + Delta for each subsequent received Object Entry. Each signed Delta is encoded using the ZigZag mapping defined in Section 5. NOT_RECEIVED, PARTIALLY_RECEIVED, and NOT_DELIVERED entries are skipped in the delta chain. Since Object Entries are sorted by (Group ID, Object ID) while Objects may arrive out of order, delta values can be negative (indicating the Object arrived earlier than the previous received Object in the list). Negative delta from reordering is a valid network state signal. 5.3. Delivery Status Codes +=======+====================+===============================+ | Value | Name | Description | +=======+====================+===============================+ | 0x00 | RECEIVED | Completely received and | | | | within delivery deadline | +-------+--------------------+-------------------------------+ | 0x01 | RECEIVED_LATE | Completely received but | | | | exceeded delivery deadline | +-------+--------------------+-------------------------------+ | 0x02 | NOT_RECEIVED | No bytes received at report | | | | generation time | +-------+--------------------+-------------------------------+ | 0x03 | PARTIALLY_RECEIVED | Partial bytes received but | | | | Object is incomplete | +-------+--------------------+-------------------------------+ | 0x04 | NOT_DELIVERED | Not received, and the Object | | | | was intentionally not | | | | delivered (see Section 5.3.4) | +-------+--------------------+-------------------------------+ Table 5 NOT_RECEIVED and PARTIALLY_RECEIVED describe Objects that a Publisher attempted to deliver but that did not arrive intact. NOT_DELIVERED describes Objects that were withheld or abandoned by design. Feedback Consumers SHOULD NOT treat NOT_DELIVERED as evidence of network loss. Liu, et al. Expires 23 May 2027 [Page 19] Internet-Draft MoQ Feedback November 2026 5.3.1. RECEIVED_LATE Determination The Feedback Publisher MUST determine Object expiration based on a locally available playback deadline: An Object is RECEIVED_LATE when its arrival time exceeds its expected playback moment. When a playback deadline is unavailable (e.g., non-real-time playback scenarios), the Feedback Publisher SHOULD report RECEIVED rather than RECEIVED_LATE. For example, suppose the application determines that an Object is expected to be available for playback at time 10.180 seconds on the Feedback Publisher's monotonic clock. If the last byte arrives at 10.195 seconds, the Object is reported as RECEIVED_LATE. If the MQF report is generated at 10.220 seconds and this is the first received Object Entry in the report, its Receive Timestamp Delta represents an arrival 25 milliseconds before the Report Timestamp. The playback deadline and the 15-millisecond lateness are not carried in the Object Entry; MQF reports the result of evaluating the application- provided deadline. Playback deadlines are often derived from an adaptive jitter buffer and differ between Media Subscribers and over time. When Optional Media Metrics are enabled, a Feedback Publisher that reports RECEIVED_LATE SHOULD include the TARGET_PLAYOUT_DELAY_MS metric (Section 5.5) so that a Feedback Consumer can interpret the deadline that was applied and compare reports from different Media Subscribers. 5.3.2. NOT_RECEIVED Reporting Timing The Feedback Publisher SHOULD report an Object as NOT_RECEIVED when one of the following conditions is met: * A subsequent Object with a larger Object ID in the same Subgroup of the same Group has arrived, but this Object has not. * The Object's expected arrival time has exceeded 2 x expected_interval (see Section 5.4.6) without arrival, and no subsequent Object is available for reference. Condition 2 covers the "last Object lost" scenario (no subsequent Object to trigger Condition 1). Liu, et al. Expires 23 May 2027 [Page 20] Internet-Draft MoQ Feedback November 2026 Condition 1 is evaluated per Subgroup. Objects of one Group can be carried in several Subgroups on separate streams, for example when temporal enhancement layers are carried in a different Subgroup from the base layer, and the streams can be delivered in any order and at different priorities. The arrival of an Object in one Subgroup MUST NOT, by itself, cause an Object in a different Subgroup to be reported as NOT_RECEIVED. For Objects carried in Datagrams, which have no Subgroup, Condition 1 applies across the Group. The Feedback Publisher MUST NOT report NOT_RECEIVED for Objects that are not yet reasonably expected to arrive, or for Objects that meet the conditions for NOT_DELIVERED (Section 5.3.4). 5.3.3. PARTIALLY_RECEIVED Applicable to Objects carried over QUIC Stream: When a Stream is terminated by RESET_STREAM or closed due to timeout, Objects with partially received data SHOULD be reported as PARTIALLY_RECEIVED. The timeout threshold used to determine whether a partially received Object should be reported as PARTIALLY_RECEIVED is application- defined. Different applications can use different thresholds according to their latency requirements. A partially received Object that other Objects depend on, such as a video reference frame, can leave the Media Subscriber unable to decode the rest of the Group. MQF reports the observation; a Media Subscriber that needs a new decodable starting point can request one using the NEW_GROUP_REQUEST parameter defined in [MoQTransport]. For Objects carried over QUIC Datagram: Since QUIC Datagrams are not retransmitted by the transport layer, any Object whose Datagram(s) are lost results in incomplete data at the Feedback Publisher. If the Feedback Publisher detects that some but not all Datagrams constituting an Object have arrived, and the remaining Datagrams are not expected to arrive (e.g., a subsequent Object has arrived or the application-defined timeout has expired), the Object SHOULD be reported as PARTIALLY_RECEIVED. If no Datagrams for the Object have arrived, the Object SHOULD be reported as NOT_RECEIVED instead. 5.3.4. NOT_DELIVERED MOQT Publishers and Relays do not always deliver every Object of a Track. They schedule by priority and can abandon Objects that would arrive too late, and a Subscriber can stop receiving a Group to move to a newer one. Reporting such Objects as NOT_RECEIVED would make deliberate scheduling decisions look like network loss, and a Feedback Consumer that adapts on loss could then reduce quality Liu, et al. Expires 23 May 2027 [Page 21] Internet-Draft MoQ Feedback November 2026 without cause. The Feedback Publisher SHOULD report an Object as NOT_DELIVERED when it has not been received and at least one of the following is true: * The upstream Publisher signalled that the Object will not be delivered, for example through an Object Status, a Prior Object ID Gap property, or an end of Group or Subgroup indication as defined by [MoQTransport]. * The stream carrying the Object was reset by the Publisher with an error code that [MoQTransport] associates with a delivery timeout or with the Publisher's decision to stop sending that stream. * The Media Subscriber itself stopped receiving the Group or Subgroup containing the Object, for example by moving to a newer Group, by canceling the stream, or by ending the subscription. NOT_DELIVERED describes why an Object is missing from the Media Subscriber's point of view; it does not identify which node withheld it. An Object reported as NOT_DELIVERED can still be missing because of congestion upstream, for example when a Relay drops low-priority Objects that it could not send in time. Feedback Consumers that need to detect such congestion can track the rate of NOT_DELIVERED Objects separately from Objects Lost. 5.4. Summary Stats Block Summary Stats { Report Interval (i), Total Objects Evaluated (i), Objects Received (i), Objects Received Late (i), Objects Lost (i), Avg Inter-Arrival Delta (i), Objects Not Delivered (i), } Summary Stats MUST always be included in every MQF report and are not controlled by the negotiation bitmap. They provide a windowed aggregate view for Feedback Consumers that do not process every Object Entry. The Report Interval window of Summary Stats is independent from the coverage of Object Entries. Object Entries MAY include Objects outside the Report Interval window (e.g., continuously reported NOT_RECEIVED entries, see Section 7.4). Liu, et al. Expires 23 May 2027 [Page 22] Internet-Draft MoQ Feedback November 2026 5.4.1. Report Interval The time window length covered by this report (varint), in microseconds. This window spans from Report Timestamp - Report Interval to Report Timestamp. RECOMMENDED value is 50000-200000 (50-200ms). 5.4.2. Total Objects Evaluated Total number of Objects (varint) evaluated within the Report Interval window. Includes Objects of all statuses. MUST equal Objects Received + Objects Received Late + Objects Lost + Objects Not Delivered. Because a later report can revise the status of an Object (Section 7.2), these counts are a snapshot taken when the report is generated. A Feedback Consumer that accumulates counts across reports needs to account for Objects that appear in more than one Report Interval window. 5.4.3. Objects Received Number of Objects (varint) with status RECEIVED within the window. 5.4.4. Objects Received Late Number of Objects (varint) with status RECEIVED_LATE within the window. 5.4.5. Objects Lost Number of Objects (varint) with status NOT_RECEIVED or PARTIALLY_RECEIVED within the window. 5.4.6. Avg Inter-Arrival Delta Average arrival interval deviation (varint, signed encoding) of consecutive received Object pairs within the window, in microseconds. Calculation method: For consecutive received Object pairs (i-1, i) sorted by arrival time within the window: delta(i) = (A(i) - A(i-1)) - expected_interval Avg Inter-Arrival Delta = mean(delta(i)) for all i Where A(i) is the arrival time of Object i, and expected_interval is the expected arrival interval. Liu, et al. Expires 23 May 2027 [Page 23] Internet-Draft MoQ Feedback November 2026 Methods to determine expected_interval (by priority): 1. A nominal Object interval supplied by the media format or application. 2. Historical average arrival interval within current session (sliding window). If neither method is available, the Feedback Publisher SHOULD use method 2 or set this field to 0. Positive values indicate Object arrival interval greater than expected (increased queuing), negative values indicate less than expected. When fewer than 2 received Objects exist in the window, this field MUST be 0. Arrival time is recorded when the last byte of an Object arrives (Section 7.1). For media in which Object sizes vary widely, such as video with periodic key frames, part of the deviation reflects Object size rather than queuing. Feedback Consumers SHOULD interpret this field over several reports rather than from a single value. 5.4.7. Objects Not Delivered Number of Objects (varint) with status NOT_DELIVERED within the window. These Objects are not included in Objects Lost. 5.5. Optional Media Metrics Optional Media Metrics immediately follow Summary Stats. Optional Metric Count (varint) specifies the number of subsequent Optional Metrics; a value of 0 indicates no optional metrics are included. Each metric uses the following MQF type/value pair. Both fields use the QUIC variable-length integer encoding defined for report Payloads in Section 5: Optional Metric { Metric Type (i), Metric Value (i), } Defined metric types are divided into two categories: Application- Layer Metrics and QUIC Layer Summary Metrics. *Application-Layer Metrics:* Liu, et al. Expires 23 May 2027 [Page 24] Internet-Draft MoQ Feedback November 2026 +====+==========================+============+=====================+ |Type| Name |Unit |Description | +====+==========================+============+=====================+ |0x02| PLAYOUT_AHEAD_MS |milliseconds|Remaining time until | | | | |playback stall at the| | | | |Feedback Publisher, | | | | |i.e., buffered but | | | | |not yet played media | | | | |duration. Smaller | | | | |values indicate | | | | |closer to stall (0 = | | | | |currently stalled). | +----+--------------------------+------------+---------------------+ |0x04| ESTIMATED_BANDWIDTH_KBPS |kbps |Bandwidth estimate | | | | |reported by the | | | | |Feedback Publisher. | | | | |The estimation method| | | | |is application- | | | | |defined. | +----+--------------------------+------------+---------------------+ |0x06| UNDERRUN_COUNT |events |Number of times | | | | |within the Report | | | | |Interval that | | | | |playback of the | | | | |associated media | | | | |Track had no media | | | | |available to play | | | | |when needed (buffer | | | | |underrun). | +----+--------------------------+------------+---------------------+ |0x08| STALL_DURATION_MS |milliseconds|Total time within the| | | | |Report Interval | | | | |during which playback| | | | |of the associated | | | | |media Track was | | | | |stalled. | +----+--------------------------+------------+---------------------+ |0x0A| TARGET_PLAYOUT_DELAY_MS |milliseconds|Playout delay | | | | |targeted by the | | | | |Feedback Publisher's | | | | |jitter buffer at | | | | |report generation | | | | |time, used to | | | | |determine | | | | |RECEIVED_LATE | | | | |(Section 5.3.1). | +----+--------------------------+------------+---------------------+ |0x0C| RECEIVE_RATE_KBPS |kbps |Object Payload bytes | Liu, et al. Expires 23 May 2027 [Page 25] Internet-Draft MoQ Feedback November 2026 | | | |of the associated | | | | |media Track received | | | | |within the Report | | | | |Interval, divided by | | | | |the Report Interval. | +----+--------------------------+------------+---------------------+ Table 6 *QUIC Layer Summary Metrics:* The following metrics expose summary information about the Feedback Publisher's local QUIC connection to the Feedback Consumer. +======+================+==============+============================+ | Type | Name | Unit | Description | +======+================+==============+============================+ | 0x10 | PEER_RTT_US | microseconds | Feedback Publisher's | | | | | local QUIC connection | | | | | smoothed RTT, | | | | | corresponding to | | | | | smoothed_rtt in RFC 9002. | +------+----------------+--------------+----------------------------+ | 0x12 | PEER_LOSS_RATE | per mille | Feedback Publisher's | | | | | local QUIC connection | | | | | packet loss rate within | | | | | Report Interval, | | | | | expressed in per mille | | | | | (e.g., 50 = 5.0%). | +------+----------------+--------------+----------------------------+ Table 7 Object Entries and Summary Stats carry the core MQF report information. Optional Metrics provide supplementary application- or transport-level observations. UNDERRUN_COUNT and STALL_DURATION_MS describe events within the Report Interval rather than a value at a single moment. A Feedback Consumer can compute the underrun frequency directly from consecutive reports, which is a common input for selecting a lower-rate representation. Liu, et al. Expires 23 May 2027 [Page 26] Internet-Draft MoQ Feedback November 2026 Because the method behind ESTIMATED_BANDWIDTH_KBPS is application- defined, values from different Feedback Publishers are not comparable unless the application defines the method. RECEIVE_RATE_KBPS is defined by this document and is comparable across Feedback Publishers. It reports the rate that was received, which is not necessarily the rate the path could carry. Neither metric replaces congestion control (Section 1.2). PEER_LOSS_RATE counts QUIC packet loss. QUIC retransmits lost data carried on streams, so packet loss does not by itself imply Object loss. Metric Types are assigned from the Optional Metrics Type Registry (Section 12). Values 0x00-0x3f are assigned by Standards Action; values 0x40-0x3fff are assigned by Specification Required; values 0x4000 and above are reserved for Private Use. A Feedback Publisher MUST NOT send a Private Use Metric Type unless the Feedback Consumer is known, through an application agreement, to interpret it the same way. The Feedback Consumer MUST ignore unrecognized Metric Types. Optional Media Metrics MAY be included in an MQF report only when both endpoints have declared OPTIONAL_METRICS in their Setup Options (Section 6). When that capability is not enabled, Optional Metric Count MUST be 0. 5.6. Report Size Control A single MQF report is RECOMMENDED not to exceed 1200 bytes, so that a report fits in a single QUIC packet and the loss of one packet does not delay the whole report. When the number of Objects to report exceeds the capacity of a single MQF report, the Feedback Publisher SHOULD: * Prioritize including recent Object Entries (largest media Object locations). * Trim the oldest Object Entries. * Ensure Summary Stats covers the complete Report Interval window (Summary Stats is not affected by Object Entry trimming). Liu, et al. Expires 23 May 2027 [Page 27] Internet-Draft MoQ Feedback November 2026 5.6.1. Encoding Example The following is an encoding structure of a typical MQF report containing delivery status of the 5 most recent Objects on the audio_response Track. Object Entries are sorted in ascending order by (Group ID, Object ID). Signed fields use ZigZag-encoded unsigned values (encoding convention at the beginning of Section 5). The Feedback Track carries the MQF_FEEDBACK_TYPE Track Property with value ORIGIN_FEEDBACK. MQF Report: Report Timestamp: 2000000 (2000000us = 2s since setup) Report Sequence: 10 (10th report) Object Entry Count: 5 (5 Objects) Object Entry [0]: (smallest media Object location, first in list) Group ID: 7 Object ID: 96 Status: 0x00 (RECEIVED) Recv Ts Delta: 189999 (ZigZag(-95000): 95ms before Report Timestamp) (First received Object, baseline=Report Timestamp) Object Entry [1]: Group ID: 7 Object ID: 97 Status: 0x02 (NOT_RECEIVED) (No Recv Ts Delta) Object Entry [2]: Group ID: 7 Object ID: 98 Status: 0x01 (RECEIVED_LATE) Recv Ts Delta: 100000 (ZigZag(+50000): 50ms later than Object 96) (Skip NOT_RECEIVED 97, baseline=Object 96) Object Entry [3]: Group ID: 7 Object ID: 99 Status: 0x00 (RECEIVED) Recv Ts Delta: 40000 (ZigZag(+20000): 20ms later than Object 98) Object Entry [4]: Group ID: 7 Object ID: 100 Status: 0x00 (RECEIVED) Recv Ts Delta: 40000 (ZigZag(+20000): 20ms later than Object 99) Summary Stats: Liu, et al. Expires 23 May 2027 [Page 28] Internet-Draft MoQ Feedback November 2026 Report Interval: 100000 (100000us = 100ms) Total Objects Evaluated: 5 Objects Received: 3 Objects Received Late: 1 Objects Lost: 1 Avg Inter-Arrival Delta: 6000 (ZigZag(+3000): avg arrival interval 3ms larger) Objects Not Delivered: 0 Optional Metric Count: 2 Optional Metric [0]: Metric Type: 0x02 (PLAYOUT_AHEAD_MS) Metric Value: 150 (playout headroom 150ms) Optional Metric [1]: Metric Type: 0x04 (ESTIMATED_BANDWIDTH_KBPS) Metric Value: 800 (estimated bandwidth 800kbps) In this example, the Track Property identifies an ORIGIN_FEEDBACK Track. Intermediate Relays forward the Track toward the Media Original Publisher without inspecting its MQF Payload. Object 97 in Group 7 is lost and Object 98 arrived late. Object 98's delta (+50ms) is significantly larger than normal interval (~20ms). Avg Inter-Arrival Delta is positive (+3ms) indicating larger-than- expected arrival intervals. PLAYOUT_AHEAD_MS is only 150ms. These signals combined indicate deteriorating network conditions. 6. Negotiation 6.1. Setup Option This extension is defined for MOQT draft-22. Endpoints declare MQF support using the MOQT_FEEDBACK Setup Option in the symmetric SETUP exchange described in [MoQTransport], Sections 6.3.2 and 9.1. Each endpoint sends SETUP as the first message on its own unidirectional control stream. Either endpoint can send first, without waiting for the other endpoint's SETUP. The MOQT version is selected during session establishment using ALPN for native QUIC or WT-Available-Protocols for WebTransport, as specified in [MoQTransport], Section 6.2. The protocol identifier for draft-22 is moqt-22. SETUP carries neither a transport version field nor a ROLE option. The SETUP message has Type 0x2F00, a 16-bit message Length, and a sequence of Setup Options bounded by that Length; there is no option count. MOQT_FEEDBACK has an even Option Type, TBD1 (experimental number 0xFE). It uses the Key-Value-Pair encoding in [MoQTransport], Section 8.3: Liu, et al. Expires 23 May 2027 [Page 29] Internet-Draft MoQ Feedback November 2026 MOQT_FEEDBACK Setup Option { Delta Type (vi64), Capability Bitmap (vi64), } Delta Type is TBD1 minus the previous Option Type in this SETUP, or TBD1 if this is the first option. Options are ordered by their decoded Type. Because TBD1 is even, the value is a single MOQT variable-length integer and no option Length field is present. These fields use MOQT vi64, not the QUIC integer encoding used in MQF report Payloads. An endpoint MUST NOT include more than one MOQT_FEEDBACK option in SETUP. An MQF endpoint receiving a duplicate MUST close the session with PROTOCOL_VIOLATION. A value that does not match this serialization is handled as KEY_VALUE_FORMATTING_ERROR under [MoQTransport], Section 8.3. An endpoint that does not recognize the option ignores it under the MOQT Setup Option rules. The option declares support for MQF report format version 0. Its Capability Bitmap has the following bit definitions: +======+====================+====================================+ | Bit | Name | Description | +======+====================+====================================+ | 0 | PUBLISH_FEEDBACK | Support publishing Feedback Tracks | | | | on this MOQT session | +------+--------------------+------------------------------------+ | 1 | OPTIONAL_METRICS | Support Optional Media Metrics | | | | (Section 5.5) | +------+--------------------+------------------------------------+ | 2 | SUBSCRIBE_FEEDBACK | Support subscribing to Feedback | | | | Tracks on this MOQT session | +------+--------------------+------------------------------------+ | 3-63 | Reserved | Endpoints MUST set these bits to 0 | | | | and MUST ignore them when received | +------+--------------------+------------------------------------+ Table 8 *Negotiation Example:* The following diagram shows logical option types and values. Other Setup Options, including any required by the transport, are omitted. On the wire, Option Types are delta-encoded as described above. The two SETUP messages are independent advertisements; their order here does not imply a response or a requirement to wait. Liu, et al. Expires 23 May 2027 [Page 30] Internet-Draft MoQ Feedback November 2026 Endpoint A Endpoint B | | | SETUP(options=[ | | {type=TBD1, value=0x06} | OPTIONAL_METRICS + | ]) | SUBSCRIBE_FEEDBACK |----------------------------------->| | | | SETUP(options=[ | | {type=TBD1, value=0x03} | PUBLISH_FEEDBACK + | ]) | OPTIONAL_METRICS |<-----------------------------------| | | | After both SETUPs: | | B -> A feedback is enabled. | | A -> B feedback is disabled. | | Optional Metrics are enabled. | 6.2. Capability Negotiation Rules Each capability bit describes the endpoint that sends the Setup Option. PUBLISH_FEEDBACK and SUBSCRIBE_FEEDBACK are complementary endpoint capabilities; they do not require both endpoints to declare the same bit. A Feedback Track from Endpoint A to Endpoint B can be established only when Endpoint A has declared PUBLISH_FEEDBACK and Endpoint B has declared SUBSCRIBE_FEEDBACK. An endpoint MUST send its SETUP and receive the peer's SETUP before establishing a Feedback Track or sending MQF Objects. An endpoint MUST NOT use capabilities remembered from an earlier session to send Feedback Track requests or MQF Objects in 0-RTT before the current exchange completes. After applying the default of zero for an omitted option, each endpoint computes the same directional result: * A-to-B feedback requires A's PUBLISH_FEEDBACK and B's SUBSCRIBE_FEEDBACK. * B-to-A feedback requires B's PUBLISH_FEEDBACK and A's SUBSCRIBE_FEEDBACK. * Optional Metrics require both endpoints' OPTIONAL_METRICS bits and do not enable either feedback direction by themselves. An endpoint that has not declared PUBLISH_FEEDBACK MUST NOT publish a Feedback Track. When an endpoint receives a PUBLISH for a Feedback Track, it MUST reject the request with REQUEST_ERROR if the peer did not declare PUBLISH_FEEDBACK or if the receiving endpoint did not declare SUBSCRIBE_FEEDBACK. Liu, et al. Expires 23 May 2027 [Page 31] Internet-Draft MoQ Feedback November 2026 Optional Media Metrics are enabled only when both endpoints have declared OPTIONAL_METRICS. An MQF report MUST NOT include Optional Metrics when that capability is not enabled. These capability rules apply to all MOQT endpoints, including Relays, independently on each MOQT session. 6.3. Behavior When Option Not Declared When a peer's SETUP does not include the MOQT_FEEDBACK option, that peer is treated as having declared a zero Capability Bitmap and does not support publishing or subscribing to Feedback Tracks. An endpoint MUST NOT publish a Feedback Track to that peer and MUST reject a Feedback Track PUBLISH received from that peer. The absence of this option does not prevent ordinary media Track operation. 6.4. Runtime Capability Change This version does not support runtime changes to Media over QUIC Feedback capability. If change is needed, MoQ session MUST be re- established. 7. Media Subscriber Behavior A Media Subscriber that publishes MQF reports acts as the Feedback Publisher for the associated media Track. This section describes that Media Subscriber behavior. 7.1. Arrival Time Recording The Media Subscriber MUST record the arrival time of each Object. Arrival time is defined as the moment when the last byte of the Object arrives at the Media Subscriber's MoQ layer. Implementation MUST use monotonic clock, unaffected by system time adjustments. Time precision SHOULD be no less than 1 millisecond, RECOMMENDED to be microsecond-level. 7.2. Delivery Status Determination The Media Subscriber MUST maintain delivery status for each known Object: * Last byte of Object arrives and within deadline: RECEIVED (0x00). * Last byte of Object arrives but exceeds deadline: RECEIVED_LATE (0x01). Liu, et al. Expires 23 May 2027 [Page 32] Internet-Draft MoQ Feedback November 2026 * Object has not arrived but is reasonably considered lost (see Section 5.3): NOT_RECEIVED (0x02). * Object partially arrived and carrying Stream is closed: PARTIALLY_RECEIVED (0x03). * Object has not arrived and was intentionally not delivered (see Section 5.3.4): NOT_DELIVERED (0x04). Object status MAY be updated in subsequent MQF. For example, from NOT_RECEIVED to RECEIVED (when a delayed Object is eventually received). Therefore, counts such as Objects Lost in Summary Stats reflect an observation snapshot at report generation time rather than final delivery statistics. 7.3. MQF Generation Timing The frequency of MQF reports is application- and deployment-defined. A Feedback Publisher needs to balance the freshness required by its Feedback Consumer against the bandwidth and processing cost of the Feedback Track. This document does not define media-specific reporting intervals or require MQF reports to be used as a session heartbeat. A Feedback Publisher MAY generate an additional report when a recent Object changes status rather than waiting for its next periodic report. 7.4. Object Entry Selection The number of Object Entries in an MQF report is not fixed. A Feedback Publisher selects Object Entries according to its reporting policy and report-size budget. When selecting Object Entries: * If not all candidate Object Entries are included, the Feedback Publisher SHOULD prioritize recently observed Objects. * An Object reported in a previous MQF report MAY be omitted when its status has not changed. * A later report can update the reported status of an Object. The absence of an Object Entry from a report does not indicate any delivery status for that Object. Each report represents the observations included at its generation time. Liu, et al. Expires 23 May 2027 [Page 33] Internet-Draft MoQ Feedback November 2026 7.5. Exception Handling * *Object Out-of-Order Arrival:* The Media Subscriber MUST record by actual arrival time without reordering. Arrival time reflects actual network behavior; out-of-order itself is a valid network signal. * *Duplicate Objects:* The Media Subscriber SHOULD identify duplicates by Group ID and Object ID, ignore duplicate arrivals, and retain the first arrival time. 8. Media Publisher Behavior A Media Publisher that terminates and interprets an associated Feedback Track acts as its Feedback Consumer. This section describes how the Media Publisher processes MQF reports for the associated media Track. 8.1. Report Consumption A Feedback Consumer uses the media Full Track Name, Group ID, and Object ID in an MQF report to associate each reported status with an Object from the corresponding media Track. MQF reports describe observations made by a Feedback Publisher. A Feedback Consumer can make valid reports available to the Application. 9. Application Usage Considerations This non-normative section illustrates conditions that can cause an application to generate feedback, the information conveyed in an MQF report, and possible actions by a Feedback Consumer. MQF conveys observations rather than control commands; adaptation strategies and coordination between decision points are application-defined. 9.1. Relay-Local Feedback Consumption Consider a live-streaming deployment that supports Relay-executed Track selection through a separate Track-switching mechanism. The application makes the same video available through a high-bitrate Track and a low-bitrate Track. A Media Subscriber configures these Tracks as acceptable alternatives and authorizes the adjacent Relay to select between them. While the Relay is forwarding the high- bitrate Track, several complete Objects arrive after their application-defined playback deadlines and the Media Subscriber's playout headroom decreases. The Media Subscriber publishes a HOP_FEEDBACK report containing RECEIVED_LATE Object Entries, a Liu, et al. Expires 23 May 2027 [Page 34] Internet-Draft MoQ Feedback November 2026 nonzero Objects Received Late count, and, when Optional Media Metrics have been enabled, a decreasing PLAYOUT_AHEAD_MS value. The adjacent Relay terminates the Feedback Track and can use the report as an application-level input in addition to transport information available on the downstream MOQT session. For example, the Relay's Track-selection logic might change the selected representation from the high-bitrate Track to the low-bitrate Track. A later series of reports showing timely Object delivery and recovered playout headroom might contribute to selecting the high- bitrate Track again. MQF identifies the affected media Track and conveys the observations, but it does not identify alternative representations, authorize Relay-executed selection, define when a switch occurs, or provide a Track-switching procedure. 9.2. Source Adaptation with End-to-End Feedback Consider an interactive conference in which a Media Original Publisher produces only one representation of a real-time video Track. A Media Subscriber receives the Track either directly with no Relay or through one or more Relays. The rate of the published representation persistently exceeds what can be delivered in time over the complete path. Suppose a report interval covers five Objects: two are RECEIVED, two are RECEIVED_LATE, and one is NOT_RECEIVED. On a direct path, or when Relays forward the media Track without republishing or transforming it, the Media Original Publisher can interpret the reported Group ID and Object ID. The Media Subscriber therefore publishes these observations as ORIGIN_FEEDBACK. When the path contains Relays, they forward the ORIGIN_FEEDBACK Track without interpreting its MQF Payload. In either topology, MQF reports whether Objects reached the Media Subscriber before their application-defined deadlines. In a cascaded topology, transport feedback on the Media Original Publisher's immediate MOQT session describes only that session and does not provide this end-to-end outcome. A Relay also has no lower-bitrate Track to select in this example and, when acting solely as a forwarding Relay, cannot modify the opaque media Payload to reduce the source bitrate. The Media Original Publisher can use a continuing pattern of late or missing Objects as one input when deciding whether to reduce the source encoding or generation rate. This is an action that neither the Media Subscriber nor a Relay acting solely as a forwarding Relay can perform on the original media source. Liu, et al. Expires 23 May 2027 [Page 35] Internet-Draft MoQ Feedback November 2026 9.3. Selecting Feedback Tracks with TopN Consider a deployment that supports the proposed Top Tracks Filter mechanism [TopTracks]. Ten Media Subscribers receive the same media Track through one or more Relays and publish separate ORIGIN_FEEDBACK Tracks. The application defines a ranking Property for feedback selection. Tracks with larger values of this Property are selected first. Each Feedback Publisher exposes the ranking value as a Relay- visible Object Property on its feedback Objects, outside the MQF Payload. The Media Original Publisher, acting as the Feedback Subscriber, requests the five Feedback Tracks with the highest values of that Property from its adjacent Relay. The candidate set is scoped to feedback for the associated media Track. The Relay executes the requested selection using the exposed Property, without interpreting or modifying the MQF Payload. As ranking values change, the selected Tracks can change according to the Track-selection mechanism. In a multi-relay deployment, the requested filter can be propagated toward the Feedback Publishers so that intermediate Relays also perform selection. For example, Relay C can request up to five Feedback Tracks from each of Relays A and B and select five from their combined candidates: Subscribers A --> Relay A --+ (Top5) | +--> Relay C --> Media Original Publisher | (Top5) Subscribers B --> Relay B --+ (Top5) Subscribers A and B are two subsets of the ten Media Subscribers. Arrows show the feedback flow; filter requests travel in the opposite direction. Each Top5 selection forwards up to five Feedback Tracks. Each branch uses the same ranking Property with comparable values and restricts its candidates to feedback for the associated media Track. This allows filtering before feedback reaches the Relay adjacent to the Media Original Publisher. Selection updates, tie handling, and timeouts follow the separate Track-selection mechanism; MQF does not define a distributed selection algorithm or require simultaneous selection changes across Relays. The Media Original Publisher receives MQF reports from up to five selected Feedback Tracks, each carrying the observations of its individual Feedback Publisher. Liu, et al. Expires 23 May 2027 [Page 36] Internet-Draft MoQ Feedback November 2026 9.4. Cache Feedback as an Optional Extension Consider a deployment in which a Relay caches a media Track and serves subsequent FETCH requests for its Objects. The Media Original Publisher supplies MAX_CACHE_DURATION as defined in [MoQTransport], Section 10.3. For example, an Object has a cache duration of ten seconds, measured from when the Relay began receiving it. The Relay evicts the cached Object after three seconds due to local resource constraints. A FETCH requesting that Object after five seconds encounters a local cache miss. The cache duration limits how long an Object can be served from a cache; it does not guarantee retention until that limit. A separate extension or application agreement could define feedback describing such misses. The Relay has direct knowledge of its cache operations and, when it retains sufficient metadata, can distinguish an Object that was cached and evicted early from one that was never cached or whose cache duration has expired. A downstream Media Subscriber cannot infer this cause solely from a missing Object. A local cache miss also does not necessarily imply a delivery failure, since the Relay might retrieve the Object from an upstream Publisher. Under such an extension, the Relay acts as a Feedback Publisher and publishes a new ORIGIN_FEEDBACK Track associated with the media Track. It uses a distinct Feedback Full Track Name and Report Sequence space. The Feedback Track follows the existing establishment, authorization, and reverse media-path binding rules. Intermediate Relays forward its MQF Payload without interpreting it. The Media Original Publisher consumes the Relay's own cache observations, rather than interpreting them as delivery outcomes observed by a downstream Subscriber. The extension could use Optional Media Metrics to convey scalar counters, such as the number of FETCH requests evaluated and the number affected by early eviction. These metrics would supplement the existing MQF report structure and would be carried only when Optional Media Metrics are enabled. The extension would define the metric identifiers and meanings, the reporting interval and counting rules, and the scope and completeness of the observations, including how to represent unavailable eviction history. The generic OPTIONAL_METRICS capability does not establish agreement on these extension-specific semantics. Cache misses would not change the meanings of Object delivery status or the Summary Stats fields, including Objects Lost. The Media Original Publisher could use these observations to assess how cache retention affects retrieval and recovery in the deployment. For example, frequent cache misses caused by early eviction could Liu, et al. Expires 23 May 2027 [Page 37] Internet-Draft MoQ Feedback November 2026 lead the Media Original Publisher to extend its own Object retention window. This can reduce the risk that a Relay's upstream retrieval fails because the Object is no longer available at the origin. Any resulting cache or application policy remains outside MQF. This example does not define cache feedback metrics or require Relays to retain eviction history. Interoperable cache feedback requires the separate extension or application agreement. 9.5. Relay-Derived Feedback from Multiple Subscribers Consider an interactive conference in which an adjacent Relay forwards the same media Track to multiple Media Subscribers. Each Media Subscriber publishes HOP_FEEDBACK describing the delivery outcome it observes. The Relay can interpret each report together with local forwarding observations, such as whether an Object was available at the Relay in time for downstream delivery and whether similar outcomes were reported by multiple Media Subscribers. A future extension could define how a Relay aggregates these observations before sending feedback upstream. For example, it could distinguish an outcome reported by one Media Subscriber from an outcome reported by several Media Subscribers, or combine several reports to limit the number of Feedback Tracks delivered to the Media Original Publisher. If the Relay makes the resulting observations available to the Media Original Publisher, it acts as a new Feedback Publisher and publishes a new ORIGIN_FEEDBACK report associated with the upstream media Track. Under such an extension, the Relay consumes the Subscriber-generated HOP_FEEDBACK reports and combines them with its local observations. It then generates a separate ORIGIN_FEEDBACK report with a new Feedback Full Track Name, Report Sequence space, and MQF Payload. The Relay does not relabel or mechanically forward the received HOP_FEEDBACK Objects. Intermediate Relays forward the new ORIGIN_FEEDBACK Track without interpreting its Payload. Such aggregated reports are not interoperable based on this document alone; an extension defining them needs to specify the represented Media Subscribers, the aggregation method, and the interpretation of each reported field. Liu, et al. Expires 23 May 2027 [Page 38] Internet-Draft MoQ Feedback November 2026 In large-audience deployments, such as a webinar with thousands of Media Subscribers, the Media Original Publisher typically needs the distribution of outcomes rather than individual reports: for example, the fraction of Media Subscribers that stalled during the last interval. Such an extension can represent per-Subscriber metrics as histograms with fixed bucket boundaries. Histograms from different Relays merge by adding bucket counts, which allows hierarchical aggregation so that the volume of feedback reaching the Media Original Publisher grows with the number of Relays rather than the number of Media Subscribers. Applications such as interactive conferencing, live streaming, cloud rendering, gaming, and live-agent media can interpret Object delivery status according to their own media format and latency objectives. 9.6. Uplink-Constrained Simulcast Publisher Consider a conference in which a participant publishes the same camera source as several simulcast Tracks, for example at 180p, 540p, and 1080p, to a Relay that forwards them to other participants. Assume that the 180p, 540p, and 1080p Tracks have the same priority. The participant's uplink capacity drops so that the 1080p Track can no longer be delivered in time. The Relay is a Media Subscriber of each simulcast Track and publishes a HOP_FEEDBACK Track for each of them. Its reports of all media Tracks show RECEIVED_LATE and PARTIALLY_RECEIVED Objects. The participant, as Media Original Publisher and Feedback Consumer, can use these reports to stop encoding the 1080p Track, freeing uplink capacity for the remaining Tracks. The Relay can, in parallel, change what it forwards downstream. It can stop forwarding the 1080p Track and let Media Subscribers select another Track based on a catalog update, or it can forward a lower simulcast Track to Media Subscribers that had selected the 1080p representation, using a Relay-executed Track selection mechanism. In both cases the downstream decoder needs a decodable starting point. When the selected Track supports dynamic Groups, the Relay or Media Subscriber can request one using the NEW_GROUP_REQUEST parameter defined in [MoQTransport], which Relays forward toward the Media Original Publisher and coalesce when several requests are outstanding. MQF conveys the observations that lead to these decisions; it does not itself request new Groups or select Tracks. Liu, et al. Expires 23 May 2027 [Page 39] Internet-Draft MoQ Feedback November 2026 9.7. Feedback for Many Media Tracks A Media Subscriber in a conference can receive many media Tracks at once, for example one video Track for each participant shown in a gallery layout. Because each Feedback Track is associated with exactly one media Track (Section 4.1), such a Media Subscriber publishes one Feedback Track per media Track for which it reports feedback. Each Feedback Track needs its own establishment exchange and Relay state, and each switch to a different representation ends one media Track and starts another, together with their Feedback Tracks. For example, with reports of about 80 bytes including framing every 100 milliseconds, a Media Subscriber reporting on 25 video Tracks sends about 160 kbps of feedback. Deployments with many media Tracks per Media Subscriber can reduce this cost by reporting only for Tracks whose observations are used, by using longer Report Intervals for Tracks of lower importance, or by relying on a future extension that carries reports for several media Tracks in one Feedback Track. Such an extension would need to identify each media Track within the report and define how Summary Stats are scoped, for example per media Track and per priority class, so that a Feedback Consumer can evaluate all Tracks that share a priority together. 10. Security Considerations MQF reports are inputs to adaptation decisions made by Media Publishers and Relays. A Feedback Publisher that reports false observations, whether by error or with malicious intent, can cause a Feedback Consumer to reduce quality for all Media Subscribers of a Track, or to keep a rate that is too high for some of them. A Feedback Consumer SHOULD treat MQF reports as advisory observations. When reports from multiple Feedback Publishers are available, a Feedback Consumer SHOULD NOT allow the reports of a single Feedback Publisher to determine a decision that affects other Media Subscribers, and SHOULD limit how quickly any single source of reports can change its behavior. A node MUST only accept a Feedback Track from a peer that is authorized to subscribe to the associated media Track. For ORIGIN_FEEDBACK, each Relay applies this check on its own session, and the Media Original Publisher applies its own authorization to the Feedback Publisher as described in Section 4.3. Feedback Tracks consume Relay state and capacity. Relays SHOULD limit the number of Feedback Tracks accepted per MOQT session and per media Track, and the rate at which MQF Objects are accepted on each Liu, et al. Expires 23 May 2027 [Page 40] Internet-Draft MoQ Feedback November 2026 Feedback Track, and MAY reject or terminate Feedback Tracks that exceed those limits. Relays that forward ORIGIN_FEEDBACK SHOULD apply such limits to each downstream peer so that a large number of Feedback Publishers cannot overwhelm the Media Original Publisher. MQF Object Payloads are opaque to Relays that forward them. They can be protected end to end between the Feedback Publisher and the Feedback Consumer, for example using the same mechanism that protects media Object Payloads. A HOP_FEEDBACK Payload that is protected end to end cannot be interpreted by the Adjacent Media Publisher when that publisher is a Relay; deployments that rely on Relay-local consumption need the Relay to have access to the Payload. 11. Privacy Considerations MQF reports describe the network conditions and media consumption of the Feedback Publisher, including which Tracks it receives, when, and how playback progresses. This information can reveal user activity and network characteristics. Feedback Track Namespaces are formed by appending fields to the media Track Namespace (Section 4.2), so a peer that can discover the media Namespace can also discover the existence of Feedback Tracks for it. Relays MUST NOT deliver a Feedback Track, or advertise its Namespace, to any peer other than the Feedback Consumer and the Relays on the path to it. A stable feedback-source-id would let observers correlate feedback across sessions. A Feedback Publisher SHOULD use a random feedback- source-id for each publication session (Section 4.2). Optional Media Metrics and Relay-visible Object Properties used for selection, such as the ranking Property in the TopN example, expose information to every Relay on the path. Feedback Publishers SHOULD include only the metrics that the Feedback Consumer needs. 12. IANA Considerations This document defines the following code points for registration: * *TBD1:* MOQT_FEEDBACK (experimental number 0xFE) in the MOQT Setup Options registry ([MoQTransport], Section 16.4), with an even Option Type and a vi64 capability bitmap value (Section 6.1). * *TBD2:* MQF_FEEDBACK_TYPE (experimental number 0x37FE) in the MOQ Properties registry ([MoQTransport], Section 16.8), with an even Property Type outside the Mandatory Track Property range and a vi64 value, scoped to Tracks (Section 4.1). Liu, et al. Expires 23 May 2027 [Page 41] Internet-Draft MoQ Feedback November 2026 * *Feedback Type Registry* (Section 4.1): - 0x00: HOP_FEEDBACK - 0x01: ORIGIN_FEEDBACK * *Delivery Status Code Registry* (Section 5.3): - 0x00: RECEIVED - 0x01: RECEIVED_LATE - 0x02: NOT_RECEIVED - 0x03: PARTIALLY_RECEIVED - 0x04: NOT_DELIVERED * *Optional Metrics Type Registry* (Section 5.5), with registration policies of Standards Action for 0x00-0x3f, Specification Required for 0x40-0x3fff, and Private Use for 0x4000 and above [RFC8126]: - 0x02: PLAYOUT_AHEAD_MS - 0x04: ESTIMATED_BANDWIDTH_KBPS - 0x06: UNDERRUN_COUNT - 0x08: STALL_DURATION_MS - 0x0A: TARGET_PLAYOUT_DELAY_MS - 0x0C: RECEIVE_RATE_KBPS - 0x10: PEER_RTT_US - 0x12: PEER_LOSS_RATE 13. Acknowledgments The authors would like to thank Cullen Jennings for his valuable review comments, proposed revisions, and insightful suggestions on application scenarios for this document. 14. References 14.1. Normative References Liu, et al. Expires 23 May 2027 [Page 42] Internet-Draft MoQ Feedback November 2026 [MoQTransport] Nandakumar, S., Vasiliev, V., Swett, I., and A. Frindell, "Media over QUIC Transport", Work in Progress, Internet- Draft, draft-ietf-moq-transport-22, 1 October 2026, . [QUIC-TRANSPORT] Iyengar, J., Ed. and M. Thomson, Ed., "QUIC: A UDP-Based Multiplexed and Secure Transport", RFC 9000, DOI 10.17487/RFC9000, May 2021, . [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 8126, DOI 10.17487/RFC8126, June 2017, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . 14.2. Informative References [quic-receive-ts] Swett, I. and J. Beshay, "QUIC Extended Acknowledgement for Reporting Packet Receive Timestamps", Work in Progress, Internet-Draft, draft-ietf-quic-receive-ts-01, 2 March 2026, . [TopTracks] Zanaty, M., "Top Tracks Filter (MOQT Pull Request #1981)", 12 October 2026, . Authors' Addresses Yanmei Liu Alibaba Inc. Email: miaoji.lym@alibaba-inc.com Liu, et al. Expires 23 May 2027 [Page 43] Internet-Draft MoQ Feedback November 2026 Minghui Jiang Email: jiangminghui2003@gmail.com Ronghua Wu Ant Group. Email: r.wu@antgroup.com Cullen Jennings Cisco Systems Email: fluffy@cisco.com Suhas Nandakumar Cisco Email: snandaku@cisco.com Liu, et al. Expires 23 May 2027 [Page 44]